british interlock hose fittings powder and other products

Hydraulic machine (aka: hydraulic press) hydraulic press is a use of hydrostatic pressure processing of metal, plastic, rubber, wood, powder and other products, machinery. It is commonly used in the british interlock hose fittings pressing process and press-forming process, such as: forging, stamping, cold extrusion, straightening, bending, flanging, sheet metal deep drawing, powder metallurgy, press-fit and so on.
Its principle is to use Pascal's law made the use of liquid pressure transmission machinery, many types. Of course, the purpose is also the root
It needs to be varied. In terms of types of liquid transfer pressure to points, there are hydraulic machines and hydraulic press two categories.
The total hydraulic pressure generated, commonly used in forging and stamping. Forging hydraulic press is divided into forging hydraulic free forging hydraulic press machine and the two kinds. Die forging hydraulic machine to use, and free forging hydraulic machines do not die. The first ten thousand tons of manufacture hydraulic press is free forging reusable hose fittings hydraulic machine. Hydraulic equipment repair and maintenance
1. Each boot load operation should be empty for 2-5 minutes, (plus a long winter can not be less than 30 minutes) before work.
2. One week later the use of new devices need to once all oil filtration and cleaning the tank, and then based on the load condition of the machine work 3-6 months to replace a fluid, cleaning a tank.
3. Since the system during use is strictly prohibited and will heat the fuel tank cap or filling hole open. After adjusting the pressure gauge switch should be closed (banned long open gauge switch, damaging the gauge). 5, is strictly prohibited outdoor use, flat seal metric hydraulic fittings measures should be rain

metal hydraulic hose and fittings

rely on electricity for molten metal hydraulic hose and fittings cutting, laser cutting is to rely on light molten metal to be cut, which
Two kinds of cutting methods to increase its cutting power as long as you can to improve their cutting speed. In cutting areas, in addition to the use of oxygen, gas cutting, the recent German research into
Rarely used. So it comes to cutting specifically refers to the former, and especially automatic cutting machine. In plasma cutting, according to the different types of plasma gas, air can be divided into
Cutter majority. In Japan, air plasma cutting machine cutting machine with automatic number of units sold in hydraulic quick coupling the market has been quite.

Plastic pipe circulating pressure impact test machine

Plastic pipe circulating pressure impact testing machine, also known as water hammer test machine for testing pipe, fittings or piping system in the case of alternating load fatigue and stress tolerance pulse peak stress. For a variety of hot and cold water piping system with rigid plastic pipes and flexible pipe systems, such as: PP-R, PP-H, PE, PEX and aluminum-plastic composite pipe and other pipes, pipe fittings.
This instrument uses a microcomputer hydraulic hose and fittings control, LED digital display, a simple, clear display, automatic alarm and other functions, various research institutes, national quality inspection institutions, large pipe manufacturers the necessary testing equipment.
Standard:
Standard GB/T18991, GB/T18992, hydraulics fittings GB/T18997, ISO10508, ISO15875, ASTM F1281, ASTM F1282, ASTM F1335, etc.
A) pressure cycles per minute, 30 ± 5 times (low voltage 0.1 ± 0.05Mpa, pressure 1.5 ± 0.05Mpa)
2) Timing accuracy: 1s
3) counting error: ± 1 ‰
4) Pressure accuracy: 0.05Mpa
5) the number of cycles set arbitrarily set :0-10000
6) Temperature range: 23 ± 2 ℃
7) Power supply: 380VAC/220VAC mix 50HZ 3kW

Installation and commissioning

Installation and commissioning
1 Handling: The machine should move the bar using a forklift or handling, the body is not allowed to tilt. Non- moving parts of the lift lock and scale .
2 Installation: The machine required level fixed on a solid foundation , and for ground handling .
3 oiling : open the case , adding 60 liters fuel tank 46 hydraulic oils .
4 Electrical connection : Connect the power cord to the machine specified power supply , observe the rotation jog motor , the motor rotation direction should be consistent with the pump requires .
5 Check Ruler : Ruler located reusable hose fittings cylinder front cover, is used to adjust the amount withheld shrink the size of the socket . Turn the adjusting the amount of shrinkage is reduced ; counterclockwise to adjust the amount of shrinkage increases. Ruler seat by spring force three screws on the pressure in the cylinder cover , hand pulling the ruler ( the direction perpendicular to the end face of the cylinder ) , the ruler should be flexible and leave the cylinder seat cover, after the release, by the spring force in the cylinder compression automatically on . Before you begin withholding , you should carefully check whether the scale stretching flexible . The ruler can not be fastened with screws on the fuel tank , otherwise it will damage the ruler.
6 pressure adjustment : machine system pressure is 20Mpa, relying on relief valve adjustment . Clockwise adjustment pressure, counterclockwise to adjust the pressure decreases.
7 speed adjustment mold : mold the pace , controlled by the shunt valve clockwise to adjust , mold speed, hydraulic hose clamps counter-clockwise to adjust , slow down the speed of the mold , but the mold too fast will make noise increases .

parher Hydraulic Hose Fittings Design Principles

Should be preferred Q / SY 015 015 pieces of pipe joints purchased varieties; When purchased items can not meet the specific connector fitting, in accordance with the standard requirements for the design. Should be preferred metric thread design; inch thread can also be designed. If the pipe joints port side of the connection parts of outsourcing, according to specifications of purchased parts port port-side design fittings oil. Material selection fittings fittings designed using high-quality carbon steel materials, chemical composition and mechanical properties, see GB / T 699. hydraulic hose machine Which has good plasticity, strength, excellent pressure resistance, is widely used in hydraulic systems. Preferred enterprise standard Q / SY 015 002 Appendix specifications. Port fittings and nozzle design port seal design port column end fittings designed using axial O-ring seal. Its port side groove type column as required. Optional fittings port threads and O-ring, and the corresponding groove dimensions and tolerances of the design requirements in Table A.1.

reusable hydraulic hose fittings are available

Parher reusable hydraulic fittings are strong, efficient, and easy to use. They come in two parts and are sold as assemblies. The stem has either a male or female pipe thread on one end. The other end has a tapered stem to fit inside the hose. The ferrule acts as a collar against which the hose is compressed when assembly is made. This connection fits firmly to the end of the hose, yet is removable and reusable on new hose when the old hose is discarded. Component parts are machined from solid brass rod and stainless steel.
reusable hydraulic hose fittings attach to the hose with a threaded connection and can easily be removed should the hose need to be repaired, unlike regular hose barb fittings. They are available in brass, electroless nickel, plated brass and stainless steel with male NPT, female NPSM and hose splicer’s options.

Parher reusable hose fitting is your best choice

Parher reusable hose fittings are the only true sanitary reusable fittings for the food and beverage industry that meet the most stringent 3-A standards. Our patented technology allows customers to reuse the expensive stainless steel jic fittings when hose assemblies need to be replaced. This can significantly enhance the cost-effectiveness of an operation as fittings typically account for 40-80% of the hose assembly costs. Assemblies with Parher fittings can be reworked by any one of our authorized fabricating distributors.
Parker reusable fittings as a convenient, high-quality, affordable reusable joints, is your best choice.